monitoring-plugins-nwc_health-10.5.1-bp155.1.4

- Update to version 10.5
  * add a temporary check for Cisco Viptela SDWAN
  * add Huawei wlan controller (not finished yet)
  * improve arista power supply/cord status checks
  * fix an uninitialized value in Arista HW check

- Update to version 10.3
  * add mode check-rtt (cisco-rttmon-mib slas)

- Update to version 10.2.1
  * update glplugin, better get_table fallback handling

- Update to version 10.1.0.3
  * fix a pull-request. Und das war damit auch der letzte
    Pull-Request, den ich in meinem Leben angenommen habe.
  * use JSON::XS in Interface.pm to avoid misleading UNKNOWN error
    message
  * suppress unknown arista sensors which are not marked as faulty

- Update to version 10.1.0.1
  * suppress unknown arista sensors which are not marked as faulty
  * check filesystems in Arista (full Log/Core stops syslog and
    accounting)
  * accept disabled sensors
  * bugfix in arista power supply

- Update to version 10.0.0.2
  * bugfix in f5 ltm detail output
  * tweak barracuda hardware-health snmp parameters

- add dependencies to perl-JSON, perl-JSON-XS, perl-File-Slurp
  to prevent errors

- Update to version 10.0
  * use json for temporary files

- Update to version 9.1
  * add Pulse Secure
  * update git with latest cisco license gedoens

- Update to version 9.0.1.1
  * remove broken line from Makefile.am
  * improve cisco license checks
  * add Versa Appliance, add HP Aruba
  * tweak barracuda snmp params for interface/route checks
  * improve Barracuda cluster-check

- Update to version 8.4
  * add bgp for huawei

- Update to version 8.3.3.2
  * bugfix in IOS cpu-load for very old models without
    CISCO-PROCESS-MIB.
  * bugfix in f5 memory-usage, correct negative values.
  * Add vpn sessions for Fortigate.
  * optimize etherlike and rmon walks.
  * save bgp peer local addresses and show them in the error case.

- Update to version 8.3.2.2
  * Blacklist storage device "junosprocfs" on JunOS (Juniper)
    devices PR #278
  * bugfix in f5 cpu-load, correct negative values
  * query LM-SENSORS-MIB only if it exists on Linux (it may hang
    even if not existing)
  * bugfix in CISCO-ENTITY-SENSOR-MIB. Scale values correctly.

- Update to version 8.3.1.1
  * bugfix in interface-stack-status (triggered when --name did
    not match)

- Update to version 8.3.1
  * add mode license-status for cisco
  * split Bluecat in AddressManager and DnsDhcpServer
  * do not use cpmCPUMemoryHCCommitted, except if you want mem
    usage > 100%
  * check the memory of all members in a cisco stack only if
    there are > 1 members
  * check the memory of all members in a cisco stack
  * bugfix in Bluecat jvm

- Update to version 8.1
  * add Bluecat Address Manager

- Update to version 8.0.0.2
  * bugfix in HOST-RESOURCE-MIB memory (Arista triggered)
  * bugfix in CISCO-ENVMON-MIB, temperatures > 200
- Update to version 8.0.0.1
  * bugfix in arista bgp, mitigate admin down

- Update to version 8.0
  * broadcast traffic is now shown as percentage of the overall
    traffic (...broadcast_in) and percentage of the available
    bandwitdth (..._broadcast_usage_in).
  * errors and discards are now calculated as percentage of all
    received/sent packets.
  * TenGig-VRF-MPLS-Dingsbums without errors and discard metrics
    are no longer treated as StackSubs.
- Update to version 7.13
  * add Vormetric Appliance
- Update to version 7.12.2
  * add some exceptions to hrDeviceDiskStorage and hrDeviceNetwork

- Update to version 7.12.1.3
  * fix a bug in mode count-routes, update glplugin

- Update to version 7.12.1.2
  * 2020-07-13 7.12.1.2
  * improve output for connect-vips
- Update to version 7.12.1.1
  * bugfix in UCD-MIB swap
- Update to version 7.12.1
  * try to fallback to ucd if neither sysUptime nor sysDescr exist